Before purchasing, please measure your car emblem size.
Features:
1. Each product has 1 color. This light must be connected to the power connector of the night license plate light. During the day when the car logo light is off, it is the same as the original car logo. When the license plate lighting is turned on at night, the LED marker lights also turn on.
2. LED lamp is waterproof and dustproof, with a service life of 100,000 hours.
3. Adopt high quality car double-sided adhesive, adhesion is extremely strong and durable!
Features:
1. Suzuki için Fit
2. Cable length: 0.6M
3. Package includes: 1pc
4. Note: If you have any questions, please contact us and we will reply you within 24 hours.
Tools prepared before installation:
Prepare the following tools: 1. Flat screwdriver 2. Cross screwdriver 3. Electrical tape 4. Towel 5. Pliers
Installation instructions:
There is double-sided tape attached to the back of the product. Please check the size of your car’s rear emblem before purchasing. When you install, you need to remove the original car rear emblem and paste this product. If the original car does not have holes, you need to drill the holes and connect the wires to the positive and negative poles of the 12V power supply in the car.
1. First, put a towel next to the body logo (to avoid scratching the body) and use a flat screwdriver to remove the logo
2. Remove the double-sided adhesive tape from the old car body logo, gently pull off the logo and clean the leftover double-sided adhesive tape.
3. Use the cross screwdriver to remove the partition panel inside the trunk, pay attention to the buckle and carefully remove the sound insulation board.
4. Install the logo light. The logo light power line runs through one of the logo positioning holes and into the trunk. Peel off the single-sided adhesive on the back of the car turn signal light, stick the car turn signal light to the body while pulling the cable, and press firmly.
5. After the installation of the logo lamp, please turn on the power supply. Connect the power supply of the taillight to the car logo lamp, so that when the small night light turns on, the car logo lamp also turns on at the same time. And find the rear license plate light power connector.
6. Unplug the plug, make a hole in the positive and negative poles, expose the wire core, connect the wire to red and black according to red, and don’t forget to wrap it with insulation tape, and finally connect the new plug! Replaces the trunk lid insulator.
Features:
1. Each product has 1 color. This light must be connected to the power connector of the night license plate light. During the day when the car logo light is off, it is the same as the original car logo. When the license plate lighting is turned on at night, the LED marker lights also turn on.
2. LED lamp is waterproof and dustproof, with a service life of 100,000 hours.
3. Adopt high quality car double-sided adhesive, adhesion is extremely strong and durable!
Features:
1. Suzuki için Fit
2. Cable length: 0.6M
3. Package includes: 1pc
4. Note: If you have any questions, please contact us and we will reply you within 24 hours.
Tools prepared before installation:
Prepare the following tools: 1. Flat screwdriver 2. Cross screwdriver 3. Electrical tape 4. Towel 5. Pliers
Installation instructions:
There is double-sided tape attached to the back of the product. Please check the size of your car’s rear emblem before purchasing. When you install, you need to remove the original car rear emblem and paste this product. If the original car does not have holes, you need to drill the holes and connect the wires to the positive and negative poles of the 12V power supply in the car.
1. First, put a towel next to the body logo (to avoid scratching the body) and use a flat screwdriver to remove the logo
2. Remove the double-sided adhesive tape from the old car body logo, gently pull off the logo and clean the leftover double-sided adhesive tape.
3. Use the cross screwdriver to remove the partition panel inside the trunk, pay attention to the buckle and carefully remove the sound insulation board.
4. Install the logo light. The logo light power line runs through one of the logo positioning holes and into the trunk. Peel off the single-sided adhesive on the back of the car turn signal light, stick the car turn signal light to the body while pulling the cable, and press firmly.
5. After the installation of the logo lamp, please turn on the power supply. Connect the power supply of the taillight to the car logo lamp, so that when the small night light turns on, the car logo lamp also turns on at the same time. And find the rear license plate light power connector.
6. Unplug the plug, make a hole in the positive and negative poles, expose the wire core, connect the wire to red and black according to red, and don’t forget to wrap it with insulation tape, and finally connect the new plug! Replaces the trunk lid insulator.
